Woods-powr-grip MRTA811LDCO Manual do Utilizador

KEEP FOR FUTURE REFERENCE INSTRUCTIONS International Version MODEL NUMBERS: MRTA8HV11DCO, MRTA811LDCO SERIAL NUMBER: ___________ (please see seri

Rev 0.0/6-14 8 MRTA8-DCO-DVS: #35077 Configurations are created by installing or removing the pad frame’s extension arms, by repositioning or removi

Rev 0.0/6-14 9 MRTA8-DCO-DVS: #35077 To Reposition (or Remove) Movable Pad Mounts 1) Remove the cotterless hitch pin from one movable pad mount. 2)

Rev 0.0/6-14 10 MRTA8-DCO-DVS: #35077 INTENDED USE LOAD CHARACTERISTICS WARNING: This lifter is NOT intended for lifting hazardous materials, such

Rev 0.0/6-14 11 MRTA8-DCO-DVS: #35077 Conversely, allowable thickness increases as load weight decreases. In addition, an operator may be able to m

Rev 0.0/6-14 12 MRTA8-DCO-DVS: #35077 OPERATION BEFORE USING THE LIFTER The operator must determine whether the lifter is capable of performing eac

Rev 0.0/6-14 13 MRTA8-DCO-DVS: #35077 Confirming the Pad Frame Configuration WARNING: Load capacity of lifter can vary, depending on pad frame conf

Rev 0.0/6-14 14 MRTA8-DCO-DVS: #35077 Sealing the Pads against the Load Move the lever on the vacuum control valve to the “APPLY” position: Pull ou

Rev 0.0/6-14 15 MRTA8-DCO-DVS: #35077 Vacuum Level on Optimal Surfaces When the lifter is attached to clean, smooth, nonporous load surfaces, it sho

Rev 0.0/6-14 16 MRTA8-DCO-DVS: #35077 TO LIFT AND MOVE THE LOAD About the Tilt Linkage WARNING: Make sure load is positioned correctly on lifter; u

Rev 0.0/6-14 17 MRTA8-DCO-DVS: #35077 Load Capacity and the Warning Light The lifter's Load Capacity is rated at a vacuum level of 16" Hg

Rev 0.0/6-14 18 MRTA8-DCO-DVS: #35077 In Case of Power Failure The lifter is equipped with 3 vacuum reserve tanks, designed to maintain vacuum tempo

Rev 0.0/6-14 19 MRTA8-DCO-DVS: #35077 TO TILT THE LOAD WARNING: Always keep hands and fingers away from bars of tilt linkage. Remember that the loa

Rev 0.0/6-14 20 MRTA8-DCO-DVS: #35077 AFTER USING THE LIFTER Place the power switch in the OFF ( ) position (blue indicator light shuts off when

Rev 0.0/6-14 21 MRTA8-DCO-DVS: #35077 MAINTENANCE WARNING: Always make sure battery is disconnected before servicing lifter. Note: One or more wi

Rev 0.0/6-14 22 MRTA8-DCO-DVS: #35077 • Keep a written record of all Periodic Inspections. If any deficiency is detected during the inspection, corr

Rev 0.0/6-14 23 MRTA8-DCO-DVS: #35077 BATTERY TEST The lifter is equipped with a battery gauge to help the operator evaluate whether the battery has

Rev 0.0/6-14 24 MRTA8-DCO-DVS: #35077 BATTERY RECHARGE Only use a battery charger supplied by or approved by Wood's Powr-Grip; other chargers m

Rev 0.0/6-14 25 MRTA8-DCO-DVS: #35077 VACUUM PAD MAINTENANCE Friction Coefficient The friction coefficient represents the lifter's ability to r

Rev 0.0/6-14 26 MRTA8-DCO-DVS: #35077 WARNING: Never use unauthorized rubber cleaners or conditioners to clean vacuum pad. To prevent liquid from c

Rev 0.0/6-14 27 MRTA8-DCO-DVS: #35077 4) Repeat steps #1-3 to verify the function of the second circuit of the vacuum system. Be sure to introduce

Rev 0.0/6-14 1 MRTA8-DCO-DVS: #35077 TABLE OF CONTENTS SPECIFICATIONS ...

Rev 0.0/6-14 28 MRTA8-DCO-DVS: #35077 AIR FILTER MAINTENANCE − LARGE (for 4.4 oz [130 ml] bowl size filters) Filter Function and Conditions Requirin

Rev 0.0/6-14 29 MRTA8-DCO-DVS: #35077 AIR FILTER MAINTENANCE − SMALL (for 1 oz [30 ml] bowl size filters) Filter Function and Conditions Requiring S

Rev 0.0/6-14 30 MRTA8-DCO-DVS: #35077 VACUUM PUMP MAINTENANCE ― THOMAS 2907CDC22/12 WARNING: Before proceeding with any maintenance, disconnect pow

Rev 0.0/6-14 31 MRTA8-DCO-DVS: #35077 VACUUM SWITCH ADJUSTMENT Vacuum Switch Function A vacuum switch controls the low vacuum warning light and the

Rev 0.0/6-14 32 MRTA8-DCO-DVS: #35077 Adjustment Procedure WARNING: Lifting capacity decreases whenever vacuum switch is adjusted to maintain lower

Rev 0.0/6-14 33 MRTA8-DCO-DVS: #35077 REPLACEMENT PARTS LIST Stock No. Description Qty. 66464 Spring Plunger with Round Knob – 1/4-20 Thread (for

Rev 0.0/6-14 34 MRTA8-DCO-DVS: #35077 LIMITED WARRANTY Powr-Grip products are carefully constructed, thoroughly inspected at various stages of prod

Rev 0.0/6-14 35 MRTA8-DCO-DVS: #35077

Rev 0.0/6-14 36 MRTA8-DCO-DVS: #35077

Rev 0.0/6-14 2 MRTA8-DCO-DVS: #35077 MAINTENANCE ...

Rev 0.0/6-14 3 MRTA8-DCO-DVS: #35077 SPECIFICATIONS Description: Designed for use with a crane or other hoisting equipment, MRTA8-DCO lifters emplo

Rev 0.0/6-14 4 MRTA8-DCO-DVS: #35077 WARNINGS Powr-Grip is pleased to offer the most reliable vacuum lifters available. Despite the high degree of

Rev 0.0/6-14 5 MRTA8-DCO-DVS: #35077 OPERATING FEATURES Note: Components featured in the following instructions for assembling, operating or maint

Rev 0.0/6-14 6 MRTA8-DCO-DVS: #35077 ASSEMBLY 1) Open the shipping container and remove all materials for restraining or protecting the vacuum lif

Rev 0.0/6-14 7 MRTA8-DCO-DVS: #35077 TO CHANGE THE PAD FRAME CONFIGURATION The lifter offers a variety of pad frame configurations to accommodate di